Savage / Anchutz Match 64 trigger spring.

This is what we do.
Post Reply
shooterer
B Poster
B Poster
Posts: 57
Joined: Thu Oct 14, 2010 8:40 am
Location: SE Wisconsin

Savage / Anchutz Match 64 trigger spring.

Post by shooterer » Thu Sep 20, 2018 6:20 am

I have a Savage Anschutz Match 64 rifle that I would like to set up for small-bore silhouette, but I can not get the trigger to adjust below 3lbs.

Would anyone know what spring I should use as a replacement and where I could buy one?

Attached is a picture of the trigger pack I have on the action.
Attachments
Trigger.jpg
Trigger.jpg (70.54 KiB) Viewed 1425 times
Stand up for what is right.... even if you stand alone.

rogersptl
A Poster
A Poster
Posts: 186
Joined: Wed May 16, 2007 8:12 pm
Location: Lander WY

Re: Savage / Anchutz Match 64 trigger spring.

Post by rogersptl » Thu Sep 20, 2018 11:03 am

Not really what you asked BUT can you readers give me an idea how to measure spring force? I assume I'd need to have a given length in order to compare them. Thanks
Close only counts with grenades and horseshoes.

ywltzucanrknrl
A Poster
A Poster
Posts: 158
Joined: Thu Aug 06, 2009 3:41 pm

Re: Savage / Anchutz Match 64 trigger spring.

Post by ywltzucanrknrl » Fri Sep 21, 2018 7:43 am

For crude methods. For measuring stretch, you can use a scale similar to a scale that weighs fish. For measuring compression, you can use a lab scale and your finger---just compress the spring under your finger while it's sitting on the scale and repeat until you get a average. If you want a better method you can buy a force gauge made to measure springs.
For the op, I used a spring out of a bic pen in my model 64 and although it did make the trigger lighter, it created variance. I ended up contacting Wolf springs and they visited with me about the length and wire diameter of the original and sent me a couple that worked well.

Jon.

thauglor
AA Poster
AA Poster
Posts: 251
Joined: Thu Aug 08, 2013 9:18 pm

Re: Savage / Anchutz Match 64 trigger spring.

Post by thauglor » Fri Sep 21, 2018 3:07 pm

To measure just the spring, you also need to know the distance it is compressed. Springs are all made with a specific spring constant; the force depends on how much it is compressed.

You can look up if that 64 is upgradable to a newer trigger. I thought all 64s can share triggers, but I don't see a rear action screw in your picture, so not sure if that is true or if it's a 64.

EQ Guy
B Poster
B Poster
Posts: 27
Joined: Sat Aug 24, 2013 2:22 pm

Re: Savage / Anchutz Match 64 trigger spring.

Post by EQ Guy » Fri Nov 09, 2018 3:06 pm

I have the same rifle and several years ago I bought a replacement trigger from Champions Choice for it. You might check to see if they are still available as an alternative.

User avatar
OldRanger
AAA Poster
AAA Poster
Posts: 951
Joined: Thu Jun 06, 2013 9:00 am
Location: Missoula, MT
Contact:

Re: Savage / Anchutz Match 64 trigger spring.

Post by OldRanger » Tue Nov 13, 2018 3:00 pm

Not sure about your specific needs, but J and P springs has top notch springs.

https://www.jnpgunsprings.com/
If she's yelling "Pineapple Congress Philadelphia Pogo-Stick" She probably forgot the safe word.

Post Reply

Who is online

Users browsing this forum: No registered users and 10 guests