What 6.5 for HP Silhouette?

More expensive to feed, but worth it.
Post Reply
jbzeus
B Poster
B Poster
Posts: 36
Joined: Sun Jul 24, 2016 5:37 pm

What 6.5 for HP Silhouette?

Post by jbzeus » Sun Apr 01, 2018 1:05 pm

There was an old thread from 2009 that asked this question. I see a number of calibers used but some bubble to the top like the 6.5x47. Wondering what the thinking is roughly nine years later.

With the 150g Sierra becoming available is the 6.5x47 still a good or even better option? Can we assume the 150g Sierra isn't too much bullet for the 6.5x47?

I see the 2017 champ shoots a 6BR. Of course every shooter is different and handles recoil differently. Maybe with her hold ability the 6BR is plenty for her?

Thinking ahead for building a HP rifle.

Jerry G
Uber Master Poster
Uber Master Poster
Posts: 2629
Joined: Wed Apr 12, 2006 2:34 pm
Location: Casa Grande, AZ

Re: What 6.5 for HP Silhouette?

Post by Jerry G » Sun Apr 01, 2018 2:02 pm

I don't think it makes much difference. The only thing that changes between all of them is the amount of powder you use. I just shot a 6.5 BR today and that little case even took down the rams. You need to shoot a heavy bullet at the rams and not much over 2600 fps to keep the bullet together longer. They all will look like they explode on impact but at 3000 fps it happens so much faster.

I shoot the 142 in my 6.5 x 47 and never had a problem when I hit them.

Cathy does loose rams.

User avatar
Jason
Uber Master Poster
Uber Master Poster
Posts: 2976
Joined: Tue Feb 28, 2006 7:36 pm
Location: Snohomish, WA

Re: What 6.5 for HP Silhouette?

Post by Jason » Sun Apr 01, 2018 6:51 pm

I have a full setup for 260 Remington and am happy with it. If I were starting over today, I'd go with 6.5 Creedmoor over the 260 Rem, 6.5x47 Lapua and definitely over any of the smaller cartridges. The 6.5 Creedmoor is now a mainstream cartridge with tons of manufacturers making barrels, dies, brass, etc. There's also a lot more load development across many times more shooters in many disciplines happening for that cartridge. Unless you have an injury or other medical issue, there's very little difference in recoil between the 6.5mm cartridges. The cartridges with more case capacity take a bit more powder to get the same velocity, but the powder weight difference compared to the bullet weight is minimal so the difference in recoil is minimal. Those cases with larger capacity can get a bit more velocity with the bigger bullets, but the 260 Rem and 6.5 Creedmoor can both do 2650fps with the newer 147gr and 150gr bullets, which is more than enough. There's no need to go to bigger cartridges like the 6.5 PRC.

jbzeus
B Poster
B Poster
Posts: 36
Joined: Sun Jul 24, 2016 5:37 pm

Re: What 6.5 for HP Silhouette?

Post by jbzeus » Tue Apr 03, 2018 5:19 pm

I do have a couple bulged disks in my lower back so I need to keep that in mind.

The consensus seems to be there is no consensus. From what I am able to deduce here and elsewhere is everyone has a favorite. I was hoping to determine "what the pros use" but it seems they each have their favorites too. Just don't want to make a faux pas right out of the gate. Maybe I should just buy one of each. :-)

Interesting the comment about Kathy losing some rams. Ya coldn't tell from her scores!

Jeff

Joaquin B
A Poster
A Poster
Posts: 231
Joined: Sat Aug 12, 2006 11:26 am
Location: Oro Valley, Arizona

Re: What 6.5 for HP Silhouette?

Post by Joaquin B » Tue Apr 03, 2018 8:23 pm

I use both the 260 and 6.5 x 47mm Lapua. Either one of those or the 6.5 Creedmoor will work.
120 grain bullets at 2650 fps for chickens/pigs/turkeys and 140/142 grainers at 2650 fps for rams.
Some folks even use the 6.5 x 55mm Swede and the 6.5 BR with good results.
Joaquin B

jbzeus
B Poster
B Poster
Posts: 36
Joined: Sun Jul 24, 2016 5:37 pm

Re: What 6.5 for HP Silhouette?

Post by jbzeus » Sat Apr 07, 2018 6:23 pm

It has been suggested I look hard at the 6.5 Creedmore. I see there is load data for up to 150g bullets. Seems that would be good for the rams.

I reload so no advantage to the Creedmore for me since I can load my own.

Anyone using 150g in 6.5x47? I don't see load data for 150g for 6.5x47.

User avatar
Another Dang 9
AAA Poster
AAA Poster
Posts: 997
Joined: Thu Dec 10, 2009 7:24 pm
Location: The Peoples Republic of Massachusetts

Re: What 6.5 for HP Silhouette?

Post by Another Dang 9 » Sun Apr 08, 2018 11:05 am

6.5 is a weird caliber that seems to shot well in all its configurations. I don't know if there is any advantage over one or the other, other than availability of brass and dies.
Its a dog eat dog world and I'm wearing milk bone underwear.
NRA Endowment Member

User avatar
SteveD
AA Poster
AA Poster
Posts: 317
Joined: Thu Sep 03, 2015 9:33 pm
Location: Phoenix
Contact:

Re: What 6.5 for HP Silhouette?

Post by SteveD » Sun Apr 08, 2018 5:53 pm

Another Dang 9 wrote:
Sun Apr 08, 2018 11:05 am
6.5 is a weird caliber that seems to shot well in all its configurations. I don't know if there is any advantage over one or the other, other than availability of brass and dies.
A few (quite a few LOL) years ago I did an analysis of the best bullets available (best determined by BC) in all calibers that were reasonable candidates for use in Silhouette.

For all bullets in all calibers up to the 30 cal Sierra 220gr MatchKing it was a 6.5mm bullet that had the highest BC. That was higher than all 6mm/.243, 25, 270 and 7mm bullets.

So yes, Another Dang 9 is right, 6.5mm bullets are an anomaly.

I you haaave to have a 6.5mm however, be sure to consider a 6.5BR. :)

There are quite a few, 6.5X47. 6.5CM, 6.5BR and there is a wildcat in Phoenix that is a 22-250 case necked up to 6.5mm, shortened 0.100" with Ackley shoulders and sides. 6.5DS.
Image

Jerry G
Uber Master Poster
Uber Master Poster
Posts: 2629
Joined: Wed Apr 12, 2006 2:34 pm
Location: Casa Grande, AZ

Re: What 6.5 for HP Silhouette?

Post by Jerry G » Mon Apr 16, 2018 11:42 am

I still say there isn't a dime worth of difference in any 6.5

ajj
AA Poster
AA Poster
Posts: 356
Joined: Mon Nov 21, 2005 9:53 am
Location: Little Rock

Re: What 6.5 for HP Silhouette?

Post by ajj » Wed Jun 06, 2018 7:23 pm

.260 Rem. Keep it simple.

Post Reply

Who is online

Users browsing this forum: No registered users and 6 guests