Damn Remington triggers

More expensive to feed, but worth it.
Post Reply
User avatar
DavidABQ
Expert Master Poster
Expert Master Poster
Posts: 1818
Joined: Mon Jul 27, 2009 9:33 pm

Damn Remington triggers

Post by DavidABQ »

I successfully bedded my BDL, cleaned up the excess bedding compound and now onto putting everything back together. So far so good. Everything send to fit, insert bolt and try out the safety. Safety arms to work, click to fire and try the trigger. Nothing! It seems that the trigger is not resetting.

Ok, how did I screw up the installing of the trigger?

Any ideas because I have none other than, "replace the trigger with (insert your favorite trigger manufacturer here) and hope I don't screw up that installation.
:x
Doodaddy
AAA Poster
AAA Poster
Posts: 684
Joined: Tue Jun 11, 2013 3:07 pm
Location: West Monroe, LA

Re: Damn Remington triggers

Post by Doodaddy »

Is the bolt cocking and the firing pin not falling or is it not cocking at all?
I am NOT Danny Hatch. Image
User avatar
DavidABQ
Expert Master Poster
Expert Master Poster
Posts: 1818
Joined: Mon Jul 27, 2009 9:33 pm

Re: Damn Remington triggers

Post by DavidABQ »

It feels like the firing pin is cocking bit not falling. There is no movement to the trigger. It seems like the sear is not resetting.
User avatar
Evelio Mc Donald
Sponsor
Sponsor
Posts: 779
Joined: Thu Feb 23, 2006 9:05 pm
Location: Wimberley, Texas

Re: Damn Remington triggers

Post by Evelio Mc Donald »

David
If the bolt is cocking, you should be able to see the back of the firing pin almost flush with the back of the bolt shroud, if it shows about 1/4" below the shroud, it means the bolt is not cocked.
There is a very small spring under the back of the sear, that normally falls out during removal of the trigger, it is tricky to re-install correctly. This spring is the one that pushes the sear back up so it will cock. Chances are that the spring is missing or not installed correctly.
Evelio.
Evelio
User avatar
DavidABQ
Expert Master Poster
Expert Master Poster
Posts: 1818
Joined: Mon Jul 27, 2009 9:33 pm

Re: Damn Remington triggers

Post by DavidABQ »

Eveilo,
There is a small spring for the sear but I thought it went under the sear near the pivot point at the front of the sear. The was even a hole for it.

That goes at the rear of the sear?
That explains a great deal.

The rifle is 1989 manufacture if that helps.
User avatar
Evelio Mc Donald
Sponsor
Sponsor
Posts: 779
Joined: Thu Feb 23, 2006 9:05 pm
Location: Wimberley, Texas

Re: Damn Remington triggers

Post by Evelio Mc Donald »

David
The spring goes in the front section of sear right by the front pivot point closest to the front of the action. Install the front pin and the sear in place, and then lift the sear, and install the spring, then hold the sear down while installing the rear pin, if everything is right, you should be able to push the sear down, and see it come back up.
Evelio
Evelio
User avatar
DavidABQ
Expert Master Poster
Expert Master Poster
Posts: 1818
Joined: Mon Jul 27, 2009 9:33 pm

Re: Damn Remington triggers

Post by DavidABQ »

The spring was the issue, it somehow popped out and was lying there in the trigger housing. Now it cocks the bolt and fires correctly, I checked the safety and it is fine too.

Thank you Evelio and everyone for the advice. After Nationals in July I will be shopping for a new trigger but until then this is great.

:-bd
Post Reply