.38-55 loads and Lyman 250 gr FN
- BrentD
- AAA Poster
- Posts: 597
- Joined: Fri Jul 26, 2013 5:48 pm
.38-55 loads and Lyman 250 gr FN
I'm looking for a load - maybe a magical load (ie, one that will shoot in the sub 2 MOA region reliably), for my .93 Marlin in .38-55.
I'm using the Lyman flatnosed bullet that is nominally 249grs, and I think I will test Unique in the range of 10-15 grs. Does that sound reasonable? I tried some old blackpowder loads that worked in the gun, sort of, before it was relined. They shot terrible, and some 4198 didn't shoot much better, hence the Unique. Does that range of powder charges (10-15 grs) sound okay, or is 15 gr a bit on the steep side?
Thanks for any constructive comments.
I'm using the Lyman flatnosed bullet that is nominally 249grs, and I think I will test Unique in the range of 10-15 grs. Does that sound reasonable? I tried some old blackpowder loads that worked in the gun, sort of, before it was relined. They shot terrible, and some 4198 didn't shoot much better, hence the Unique. Does that range of powder charges (10-15 grs) sound okay, or is 15 gr a bit on the steep side?
Thanks for any constructive comments.
- psteiger
- AAA Poster
- Posts: 773
- Joined: Fri Jun 09, 2006 10:45 am
- Location: Friendswood, Texas
Re: .38-55 loads and Lyman 250 gr FN
I use 10.0g of Unique behind a hunters supply 260g cast bullet in my Marlin and 26.1g of IMR 4895 behind an Oregon trail 240g bullet in my Winchester. I tried 5744, 3031 and they didn't work as well for me. I use .381 bullets, as you know the proper size bullet is most important. The Marlin seems to like loads 1200fps ish. The Winchester is an animal and shoots everything. Good luck! YMMV etc............
- psteiger
- AAA Poster
- Posts: 773
- Joined: Fri Jun 09, 2006 10:45 am
- Location: Friendswood, Texas
Re: .38-55 loads and Lyman 250 gr FN
If it's relined, it might have a .375 bore. Check it. I think you know all this stuff, but just in case.
- BrentD
- AAA Poster
- Posts: 597
- Joined: Fri Jul 26, 2013 5:48 pm
Re: .38-55 loads and Lyman 250 gr FN
It is and it does, so the "modern" dimensions for bullets and brass are appropriate.
That's a healthy dose of 4895. I don't think I ever explored that high.
I'll start the Unique experiments at 10g and see what happens.
That's a healthy dose of 4895. I don't think I ever explored that high.
I'll start the Unique experiments at 10g and see what happens.
- Taps
- A Poster
- Posts: 187
- Joined: Fri Jan 23, 2009 7:23 pm
- Location: Bogan Gate NSW Australia
Re: .38-55 loads and Lyman 250 gr FN
10gr of Unique ( or actually our Aussie made AP-70, which is very close ) works well in all 3 of my .38-55 Winchesters. Takes down rams too!
Taps
- BrentD
- AAA Poster
- Posts: 597
- Joined: Fri Jul 26, 2013 5:48 pm
Re: .38-55 loads and Lyman 250 gr FN
Thank you Daniel,
I will load some in a few minutes. 10 seemed on the light side to me, but apparently not, so that's what I'll start with.
I will load some in a few minutes. 10 seemed on the light side to me, but apparently not, so that's what I'll start with.
-
- B Poster
- Posts: 32
- Joined: Mon Aug 15, 2016 11:58 am
- Location: Fredericksburg VA
Re: .38-55 loads and Lyman 250 gr FN
Brent
Lyman has a newer mold version of that bullet that as cast in bp alloys drops about 0.382 to fit oversize bores the older molds will drop 378 or so'
and youtube shows Wind Whitehill---sadly just deceased--hitting an 800 yd gong routinely with 10 grains Unique in a marlin 336 lever action in 38-55
Lyman has a newer mold version of that bullet that as cast in bp alloys drops about 0.382 to fit oversize bores the older molds will drop 378 or so'
and youtube shows Wind Whitehill---sadly just deceased--hitting an 800 yd gong routinely with 10 grains Unique in a marlin 336 lever action in 38-55
-
- B Poster
- Posts: 87
- Joined: Wed Nov 24, 2010 7:20 pm
Re: .38-55 loads and Lyman 250 gr FN
Try RL7. Look up the listed min and max and do a little testing. You should be happy!
T
T
- BrentD
- AAA Poster
- Posts: 597
- Joined: Fri Jul 26, 2013 5:48 pm
Re: .38-55 loads and Lyman 250 gr FN
I shot a bunch of different loadings of Unique tonight. From 10 grs up to 12. The low end loads shot about 1.5" wide and 12" tall. The higher charges shot 5" wide and 10" tall. Yes, I positioned the powder on the primer before every shot. But no love.
Tonight I'll revisit the best of these with a slight variation added to the loading per a friend's phone call last night. I'll also try some 4198 and some 4227. Neither have been great for me before, but I'm willing to revisit them with this newly relined barrel.
Tonight I'll revisit the best of these with a slight variation added to the loading per a friend's phone call last night. I'll also try some 4198 and some 4227. Neither have been great for me before, but I'm willing to revisit them with this newly relined barrel.