Pharr stocked 1712 ?

This is what we do.
Post Reply
old sparky
B Poster
B Poster
Posts: 84
Joined: Sat Mar 14, 2009 4:19 pm
Location: Arizona

Pharr stocked 1712 ?

Post by old sparky »

I had my 1712 put in a Pharr stock by Evelio a couple years back. He made it like I ask and his work is perfect. When I got it back I took it out and sighted it in off a bench but didn't spend much time. I had other irons in the fire then crashed a couple horses, and gained some weight. I have been thinking about shooting in a match so I took it out yesterday to the range. Problem is I cant see thru my scope shooting offhand. I forced myself to try shooting by using allot of cheek pressure and pulling the stock into my face. Wasn't too long tell my back was killing me., still is today. My fat face needs to go to the right some more. So where do I go from here? Hey I ask for it. I m sure Beckley will tell me to loose some weight and shut up. Ha Ha
User avatar
dustinflint
Expert Master Poster
Expert Master Poster
Posts: 1530
Joined: Tue May 17, 2011 12:13 pm
Location: Baton Rouge, Louisiana

Re: Pharr stocked 1712 ?

Post by dustinflint »

Mount your scope higher.

Dustin
SqHunter
AAA Poster
AAA Poster
Posts: 567
Joined: Wed Oct 14, 2009 11:39 am

Re: Pharr stocked 1712 ?

Post by SqHunter »

I tend to have the same problem. With the Pharr stock your best bet would be to raise your scope. I can't shoot my rifle at all with conventional height rings, but it fits well with a set of custom made high rings. Give it a try.

As a last resort, consider one of Wayne Merrier's stocks. Years ago he made one for me without a cheek piece that fit very well, the result was similar to cast off. I wish I would have kept it. If I was in the same position today I believe I would try one of the Wooster stocks, the diagrams I have seen suggest that his stocks have more lateral relief than the Pharr, on par with the Anschutz factory stock. I did not go through with that project though so can't say for sure.
User avatar
Jason
Uber Master Poster
Uber Master Poster
Posts: 3002
Joined: Tue Feb 28, 2006 7:36 pm
Location: Snohomish, WA

Re: Pharr stocked 1712 ?

Post by Jason »

The Pharr stocks are designed to let you mount your scope higher and therefore have your head more erect for better balance while still having cheek weld. What you're dealing with is expected and a good thing. You just need taller scope rings.
old sparky
B Poster
B Poster
Posts: 84
Joined: Sat Mar 14, 2009 4:19 pm
Location: Arizona

Re: Pharr stocked 1712 ?

Post by old sparky »

Thanks. My rings are .75 I will try blocking it up and take a measurement. thanks, Jim
User avatar
Jim Beckley
Master Poster
Master Poster
Posts: 1158
Joined: Tue Jan 23, 2007 7:54 pm
Location: Cave Creek, Arizona

Re: Pharr stocked 1712 ?

Post by Jim Beckley »

Pal if I told you to loose some weight, that would be the pot calling the kettle black!
U.S. Army-Donating blood since 1775.
old sparky
B Poster
B Poster
Posts: 84
Joined: Sat Mar 14, 2009 4:19 pm
Location: Arizona

Re: Pharr stocked 1712 ?

Post by old sparky »

Jim Beckley wrote:Pal if I told you to loose some weight, that would be the pot calling the kettle black!
Thing is I knew you could take a jab! And I had to say lose weight myself
Post Reply