Best trigger for CZ452 standar class

chango2013 · Post by **chango2013** » Thu Aug 23, 2012 3:08 pm

i have one cz and i want to change the trigger i will only use the rifle for standar class
any clues which one to buy?
thanks

shooterer · Post by **shooterer** » Fri Aug 24, 2012 5:08 am

I installed the yodave trigger kit in my 452. Very easy to do and I have been happy with it.

Sancho · Post by **Sancho** » Sat Aug 25, 2012 4:53 pm

I put in the Automated Slutions sear and spring. Got the trigger safely down to 10 ish ounces. You do have to remove just a bit of stock material ( not hard)

Greencb · Post by **Greencb** » Tue Sep 11, 2012 8:00 pm

I went with Timney works very well.

OLd_Sarge · Post by **OLd_Sarge** » Fri Sep 21, 2012 6:09 am

Greencb wrote:I went with Timney works very well.

I did the same,
I had to modify the Timney sear and in-let the stock, for mine, FYI
My trigger is nice and pass's the test @ 2lb 2oz, breaks like an icicle and no over-travel

OLd_Sarge · Post by **OLd_Sarge** » Fri Sep 21, 2012 11:48 am

FYI if you want to know more about Timney trigger issues you could run, into, and the fix, go here;
I hope it is OK to post a link here, if not let me know guys.

http://rimfireshooting.com/index.php?showtopic=8776

teetertotter · Post by **teetertotter** » Sat Sep 22, 2012 2:57 pm

Since there is no pound weight limit in standard class, but a SAFE weight, you might want to first spend .60 cents at the hardware store for #144 spring and install. I found no creep in the trigger. Problem I had was, could not get it up to a 2 lb trigger, even adding washers.

I bought a #143 spring and cut it a little shorter than the OEM spring and had NO creep at 2 lb 2 oz setting. After approx 3000 rounds, I rechecked the trigger weight and was under 2lbs. It still has no trigger creep after 1-1/2 years. I still have more spring adjustment when required.

Replacement spring from the hardware store might be for you?

staff3704 · Post by **staff3704** » Sun Oct 21, 2012 9:40 am

I used a Brooks kit on a CZ scout that had a heavy trigger and tons of creep. The kit comes with different springs for pull weight and slevees to eleminate creep. When I finished I had just under 2 lbs pull (which I like) and no creep. There are several good ways to do It - your choice. But just do it. You'll be glad you did.

pbansen · Post by **pbansen** » Sun Oct 21, 2012 5:00 pm

I have two 452's - one with a Timney trigger and one with the YoDave kit. They're both creep-free, crisp and the same weight (~ 2 lbs 3 ozs). Because the Timney requires some inletting work to fit in a 452 stock, I would recommend going with the YoDave kit unless you just have to have a Timney. The other option is an adjustable sear from DIP. I have one but have not yet installed it - have not felt the need to go beyond the excellent trigger that the YoDave kit yielded.

Pete Bansen
Truckee, California

Best trigger for CZ452 standar class

Best trigger for CZ452 standar class

Re: Best trigger for CZ452 standar class

Re: Best trigger for CZ452 standar class

Re: Best trigger for CZ452 standar class

Re: Best trigger for CZ452 standar class

Re: Best trigger for CZ452 standar class

Re: Best trigger for CZ452 standar class

Re: Best trigger for CZ452 standar class

Re: Best trigger for CZ452 standard class